Electricity FAQ (Frequently Asked Questions)
Electricity is a form of energy that starts with atoms. Atoms are too small to see, but they make up everything around us. An atom has three tiny parts: protons, neutrons, and electrons. The center of the atom has at least one proton and one neutron. At least one electron travels around the center of the atom at great speed. Electricity can be created by forcing electrons to flow from atom to atom.
Most electricity used in the United States is produced at power plants. Various energy sources are used to turn turbines. The spinning turbine shafts turn electromagnets that are surrounded by heavy coils of copper wire inside generators. This creates a magnetic field, which causes the electrons in the copper wire to move from atom to atom.
Electricity leaves the power plant and is sent over high-power transmission lines on tall towers. The very strong electric current from a power plant must travel long distances to get where it is needed. Electricity loses some of its strength (voltage) as it travels, so transformers, which boost or “step up” its power, must help it along.
When electricity gets closer to where it will be used, its voltage must be decreased. Different kinds of transformers at utility substations do this job, “stepping down” electricity’s power. Electricity then travels on overhead or underground distribution wires to neighborhoods. When the distribution wires reach a home or business, another transformer reduces the electricity down to just the right voltage to be used in appliances, lights, and other things that run on electricity.
A conductor carries the electricity from the distribution wires to the house meter box. The meter measures how much electricity the people in the house use. From the meter box, wires run through the walls to outlets and lights. The electricity is always waiting in the wires to be used.
Electricity travels in a circuit. When you switch on an appliance, you complete the circuit. Electricity flows along power lines to the outlet, through the power cord into the appliance, then back through the cord to the outlet and out to the power lines again.
Electricity travels fast (186,000 miles per second). If you traveled that fast, you could travel around the world almost eight times in the time it takes to turn on a light! And if you had a lamp on the moon wired to a switch in your bedroom, it would take only 1.28 seconds after you flipped the switch for electricity to light the lamp 238,857 miles away!
Figures used to arrive at the numbers:
• Speed of light: 186,000 miles/sec
• Average distance to the moon: 238,857 miles
• Circumference of the earth: 24,902 miles (equatorial), 24,860 miles (polar)
Volts, amps, and watts measure electricity. Volts measure the pressure under which electricity flows. Amps measure the amount of electric current. Watts measure the amount of work done by a certain amount of current at a certain pressure or voltage.
To understand how they are related, think of water in a hose. Turning on the faucet supplies the force, which is like the voltage. The amount of water moving through the hose is like the amperage. You would use lots of water that comes out really hard (like a lot of watts) to wash off a muddy car. You would use less water that comes out more slowly (like less watts) to fill a glass.
Watts = Amps x Volts
Amps = Watts ÷ Volts
There are about 240,000 miles of high-voltage transmission lines in the United States and millions of miles of distribution lines carrying electricity to our homes, schools and businesses.
No! Someone can be shocked by electricity and survive. But when we say someone has been electrocuted, it means they have been killed by electricity.
You can’t see electricity when it is flowing through a circuit. But if electricity leaves the circuit – like when someone is shocked – you can see a spark. The spark isn’t electricity itself. It is a flame that happens when the electricity travels through the air and burns up oxygen particles.
Neither! In the wires of an electrical circuit, the electrons are always jiggling around. When a circuit is closed to run an appliance or a light bulb, the electrons jiggle a lot and travel through the wire. When the circuit is open, all the electrons just jiggle where they are – kind of like running in place.
It’s just the nature of electricity to move from an area of higher voltage to an area of lower voltage, if given a path to travel there. The ground is simply the lowest-voltage area around, so if you give electricity a path to the ground, it will take it, no questions asked! When electricity goes into the ground, the earth absorbs its energy.
It is easier for electricity to keep flowing through the power line than to go through the bird. But if a bird with large wings touches a power line and a tree or power pole at the same time, it provides electricity with a path to the ground, and could be shocked. And if a bird touches two wires at once, it will create a circuit – electricity will flow through the bird and likely electrocute it.
The shock you feel when you touch an object after walking on carpet is static electricity. When you drag your feet across carpet on a dry day, electrons from the carpet get transferred to your body. If you then touch a piece of metal, such as a doorknob, the electrons jump to the metal and you’ll feel a shock.
Lightning is a large discharge of static electricity. During a thunderstorm, clouds build up a charge. When there is a big difference in charge between the cloud and its surroundings, the cloud discharges a lightning bolt.
One lightning strike can carry between 100 million and 1 billion volts. (100 million volts is the equivalent of 8 million car batteries.)
Yes, it does. Because water conducts electricity, when lightning strikes water it spreads out along the surface. Any fish near the surface of the water get electrocuted.
According to Guinness World Records, Roy G. Sullivan, a former U.S. park ranger, was struck by lightning seven times over the course of his 35-year career. Lightning has burned off his eyebrows, seared his shoulder, set his hair on fire, injured his ankle, and burned his belly and chest.
Ben Franklin’s famous key did give off an electric spark. But lucky for Franklin, the kite was just drawing small electrical charges from the air. If the kite had actually been struck by lightning, Franklin would have been killed!
There is a very small chance that a lightning strike could surge through phone lines or through the wires of an electrical appliance. If you were to touch a phone or appliance at just that moment, you could be shocked.
A chemical reaction within the battery forces electrons to move.
There is not enough voltage in a regular household battery to cause a shock. However, car batteries are powerful enough to shock so you should never tamper with them.
Water and electric hair dryers are a dangerous combination! In the early 1980s, hair dryers falling into bathtubs or sinks filled with water caused about 18 deaths per year. Since 1991, hair dryer manufacturers have been required to include GFCIs (ground fault circuit interrupters) on dryer cords. GFCIs cut off electricity to prevent serious shock. Thanks to these devices, the number of hair dryer related deaths has dropped to an average of two per year.
Yes! An electric eel uses chemicals in its body to manufacture electricity. A large electric eel can produce a charge of up to 650 volts, which is more than five times the shocking power of a household outlet.
Inside the cells of the heart, tiny electrical currents fire in a steady rhythm. If that rhythm is disrupted due to disease or injury, a heart attack can occur. A defibrillator shocks every cell in the heart at the same time, so they all start up again in rhythm. It’s like each cell is dancing to the same beat!
The wire inside a light bulb is called a filament. It is made of tungsten, a metal that stays solid at very high temperatures. Electricity flows through the tungsten filament, causing it to heat up and glow. The glow gives off light. Inside a light bulb is a vacuum—in other words, all the air has been removed from inside the glass bulb. (If there were air inside, the wire would burn up.)
LEDs don’t get particularly hot and thus don’t waste energy on heat. LEDs are illuminated solely by the movement of electrons in a semiconductor material. A semiconductor is a material with electrical conductivity (meaning the ability to transfer electrical energy) between that of a conductor and an insulator (hence the prefix “semi”). Inside an LED, when an electrical current passes through the semiconductor material, electrons move through the material and drop to other energy levels, and in the process, they emit photons of light. LEDs are becoming an increasingly important and common light source because of their high degree of energy efficiency. LEDs use up to 20% less energy than CFLs and up to 90% less energy than incandescent light bulbs.
Compact fluorescent lights (CFLs) and other fluorescent light bulbs contain gases (argon and mercury vapor) that produce invisible ultraviolet (UV) light when stimulated by electricity. When the UV light hits the white phosphor coating inside the fluorescent bulb, the phosphor illuminates or “fluoresces,” changing the UV light into visible light. CFLs are very energy-efficient, using only about one-fifth the energy of a standard incandescent bulb. This is because all of the electricity they use goes toward creating light, whereas the energy used by standard incandescent bulbs creates heat as well as light.
Producing Electricity
The energy resources used to generate electricity can be divided into two categories:
Nonrenewable Resources
Nonrenewable resources cannot be replenished. We can make these supplies last longer by using them wisely, but when they are gone we will not have any more.
Fossil Fuels
The majority of electricity used in the United States is generated at power plants that burn fossil fuels to heat water and make steam. The steam is highly pressurized and directed at turbine blades to make them spin.
The three forms of fossil fuels are coal, oil and natural gas. They are known as fossil fuels because they were formed in the earth from the remains of organic matter like animals or plants that lived long ago.
Coal is a hard, black, rock-like substance made up of carbon, hydrogen, oxygen, nitrogen and sulfur. The precursor to coal, called peat, is used as an energy source in many countries. Coal is found in many parts of the U.S. and throughout the rest of the world. Coal is extracted from the ground at large mines.
Oil is a liquid fossil fuel, sometimes also called petroleum. It is found underground within porous rocks. Oil rigs must drill down to deposits deep below the earth’s surface to obtain oil. About one fifth of the oil and petroleum products (such as gasoline, heating oil and other products) used in the United States comes from outside our country.
Natural gas is made up primarily of a gas called methane. Methane gas is highly flammable and burns very cleanly. Natural gas is usually found underground along with oil. Natural gas supplies are abundant from sources in the United States and Canada.
Nuclear Power
Nuclear power plants use the heat from splitting atoms to convert water into the steam that turns turbines. These plants rely on uranium, a type of metal that must be mined from the ground and specially processed. Fuel rods containing uranium are placed next to each other in a machine called a nuclear reactor. The reactor causes the uranium atoms to split, and in so doing, they release a tremendous amount of heat.
Renewable Resources
Renewable energy resources can be replenished in a short period of time, so they will never be all used up. Energy companies throughout the country are using renewable resources more and more to generate electricity.
Biomass
Biomass is organic matter, such as agricultural waste, and wood chips and bark left over when lumber is produced. Biomass can be burned to heat water to make steam, which turns a turbine to make electricity. It can also be converted into a gas, which can be burned to do the same thing.
Biomass includes energy crops like wood, straw, and other crops grown primarily for use as a fuel. Energy crops are renewable, but some, like trees, take a long time to grow. Farmers can grow trees on some of their land instead of wheat or other kinds of food. The wood is harvested regularly, cut into small chips and burned to provide heat or run small electric power plants.
A fuel generated from biomass is methane gas, a by–product of decay in landfills. As garbage rots in the ground, it gives off gases that can be collected and burned to produce heat or electricity.
Geothermal Energy
The word geothermal comes from the Greek words geo, for earth, and therme, for heat. So geothermal means “earth heat.” Geothermal energy is steam (or hot water that has been converted to steam) from deep inside the earth.
Our planet’s interior is very hot – at its core, 4000 miles deep, temperatures may reach over 9000°F. This heat is continuously conducted from the earth’s core to the surrounding layer of rock, the mantle.
There are some places around the earth where magma (hot molten earth from the mantle) pushes up through cracks into the crust near the earth’s surface. Magma can heat nearby rock and water as hot as 700°F. Some of this hot water reaches the earth’s surface as hot springs or geysers, and some stays trapped deep underground in cracks and porous rocks. This hot water can be used directly or converted into steam to turn turbines that generate electricity.
Hydrogen
Hydrogen is a colorless, odorless gas. Hydrogen can be converted into electricity through a chemical reaction in a device called a fuel cell. Converting hydrogen into electricity produces no pollution – only water and heat.
If the hydrogen comes from a renewable resource like landfill gas, fuel cells are considered renewable. However, if it comes from a nonrenewable resource like fossil fuels, fuel cells are considered nonrenewable. Whether a fuel cell is using a renewable energy source depends on the source of the hydrogen fuel.
Today, there are already some cars that run on hydrogen. In the future, hydrogen will be used to fuel vehicles and airplanes and to provide electricity to buildings.
Hydropower
Hydroelectric plants use the power of falling water to turn the turbines that help generate electricity. Water that is stored behind a dam is released and directed through special tubes to flow against the blades of turbines and make them turn. Most hydropower facilities are found in hilly or mountainous areas. The most famous hydroelectric facility in the country is Hoover Dam.
Ocean Energy
Ocean energy is a form of hydropower. Oceans cover more than 70 percent of the earth’s surface, making them the world’s largest solar collectors. The ocean stores thermal (heat) energy, which can be used to generate electricity using special turbine generators.
The energy of the ocean’s waves and tides can also be used to generate electricity with dams that force ocean water through turbines, or with buoys embedded with turbines that spin as they shift with the movement of waves. This is called tidal energy, or wave power. The world’s first wave power station was built on the Scottish island of Islay. Other wave power stations are located in Mutriku Bay, Spain; Jaffa Port, Israel; Kaneohe Bay near Oahu, Hawaii; and Cobscook Bay on the East Coast of the United States near Eastbrook, Maine.
Scientists and engineers around the world are working on systems to use the ocean’s energy on a large scale.
Solar Energy
Solar energy is generated without a turbine or electromagnet. Special panels of solar cells, or modules, can capture sunlight and convert it directly into electricity. These panels are known as photovoltaic, or PV. (Photo is Greek for light, and voltaic pertains to electricity.) The electricity they produce can be used right away, fed into the power grid for others to use or stored in a battery so it is also available on cloudy days.
Wind Power
Wind power is renewable energy that uses the force of the wind to spin turbines. These spinning turbines generate electricity.
Most wind power is produced at wind farms, which are large groups of turbines in consistently windy locations. A very large wind farm can generate enough electricity for all the homes in a city of about one million people. Small wind turbines can be used for individual homes, businesses and boats. They can be used to pump water or the electricity can be stored in large batteries for use at another time.
Pioneers of Electricity
Benjamin Franklin (1706–1790)
Despite the popular story, Benjamin Franklin probably did not tie a key to a kite and fly it in a lightning storm. Franklin did, however, perform many experiments to learn more about electricity. One year Ben Franklin wanted to use electricity to kill a turkey for Christmas dinner. While checking his equipment, he touched two parts at the same time and got a big shock. His whole body vibrated, and his arms were numb until the next morning. He was lucky he wasn’t burned or electrocuted! Franklin believed that lightning was a flow of electricity taking place in nature. He knew the dangers and probably did not want to risk electrical shock by flying a kite in a storm. In 1752, Benjamin Franklin’s electricity experiments led him to invent the lightning rod, which when placed at the top of a barn, church steeple or other structure, conducts lightning bolts harmlessly into the ground.
Michael Faraday (1791–1867)
Michael Faraday invented the generator in 1831. Before then, all useful electricity was supplied by batteries. Faraday’s generator provided a source of current that did not depend on batteries.
Lady Augusta Ada Byron, Countess of Lovelace (1815–1852)
Ada Lovelace is considered the world’s first computer programmer. Daughter of the English poet, Lord Byron, Lovelace worked for a mathematician and inventor named Charles Babbage. Together they developed what they called “the Analytical Engine” – a mechanical computer that used gears and ratchets and could be programmed using punched cards. Lovelace, who was an accomplished mathematician, created the programming code that ran this machine, based on a binary system in which all numbers are represented as a series of zeroes and ones. The computer world honored her in the 1970s when a programming language adopted by the United States Defense Department was named Ada.
Alexander Graham Bell (1847–1922)
Alexander Graham Bell invented a way to transmit speech electrically: the telephone. Bell wanted to improve upon the telegraph, which allowed people to transmit a code of dots and dashes through an electrical wire. He and his assistant, Thomas Watson, found a way to convert the tones of the human voice into varying electronic currents in a wire and to reproduce them as audible speech through a receiver. In 1876, Bell spoke the first sentence transmitted over this new device: “Watson, come here, I want you.” The telephone was exhibited at the 1876 Centennial Exposition in Philadelphia, Pennsylvania.
Thomas Alva Edison (1847–1931)
Thomas Alva Edison invented the phonograph, the motion picture camera and more than 1,000 other things. Edison is best known for inventing the incandescent light bulb in 1879. Prior to the incandescent bulb, the world relied on oil lamps and natural gas to light the night. Edison’s bulb consisted of carbonized cotton filament housed in a vacuum inside a glass bulb. The current flowing through the filament would cause it to radiate a steady glow. The vacuum was needed to keep the filament from burning up.
While still working on the light bulb, Edison began thinking about an electric system that would provide electricity from a central power station and deliver it to homes and businesses. He designed the country’s first central electric power system, which began operating in 1882 and delivered direct current electricity to 85 customers in a 1-mile-square area in lower Manhattan. By 1902, only 20 years after Edison’s system began operations, there were 3,500 different electric systems in the United States alone.
Lewis Howard Latimer (1848–1928)
Lewis Howard Latimer was a pioneer in the development of the electric light bulb. He was the son of a former slave, and was the only African American member of Thomas Edison’s research team of noted scientists. While Edison invented the incandescent bulb, it was Latimer who developed and patented the process for manufacturing the carbon filaments within the bulb.
Granville Woods (1856–1910)
Granville Woods had prolific inventive skills and made ingenious contributions to mass transit. Woods patented a telephone transmitter in 1885, which was bought by Bell Telephone. He then founded the Woods Electric Company in New York City, which manufactured and sold telephone, telegraph, and electrical instruments. His most important invention was the induction telegraph system in 1887, a method of informing an engineer of trains immediately in front of and behind him, thus ensuring safer rail travel. Of the more than 60 patents that Woods registered, the majority were concerned with railroad telegraphs, electrical brakes and electrical railway systems.
Nikola Tesla (1856–1943)
You may know the Tesla as a high-end electric vehicle, but Nikola Tesla lived and died long before the invention of the car that bears his name. He is best known for inventing the alternating-current (AC) electrical system, the predominant electrical system used worldwide today. Tesla also created the 3-phase system of electric power transmission, and the “Tesla coil,” an induction coil still used in radio technology.
In 1884, the Serbian American engineer appealed to Thomas Edison to help finance and develop his AC motor and electrical system. But Edison was keen on promoting the less-efficient direct current (DC) system, so Tesla then went to George Westinghouse, who did fund his AC induction motors and devices. These soon took off in popularity, as they didn’t create sparks or require permanent magnets to work. Instead, Tesla’s devices used a more efficient rotating magnetic field, a design still found in most electric motors nowadays. Although Tesla’s popular inventions got him on the cover of Time magazine in 1931 and have prevailed through time, he died a poor man in 1943 after years devoted to projects that did not receive adequate financing.
Electric Vehicles
Electric vehicle (EV) technologies have grown a lot since 1999 when the first hybrid EV was introduced. Today, a variety of all-electric EVs and hybrid gasoline/electric EVs are available, and industry experts anticipate there will be over a million EVs on the roads this decade. EVs are popular for many reasons:
- They help reduce pollution.
- They cost less to run than gasoline vehicles.
- They help reduce our dependency on gasoline.
Battery Electric Vehicles
Battery EVs run entirely on electrical energy. Instead of a fuel tank, batteries store the electricity that is used to operate the vehicle. These batteries can be recharged by plugging the vehicle into a special high-voltage charging station or standard 120-volt or 240-volt household outlets. It takes anywhere from 2 to about 20 hours to recharge the battery, depending on the vehicle’s charger and the voltage used. The batteries store the electricity until the vehicle is driven.
Early types of battery EVs included golf carts, scooters and other vehicles used for short trips at low speeds. With rapid industry growth this decade, battery EVs can accommodate both city and highway driving needs. Smaller models designed for urban use can travel 30–75 mph and go 50–85 miles on a charge. The high-end Tesla can reach speeds of 150 mph and travel more than 300 miles on a single charge.
Under the hood, a battery EV consists of an electric motor, one or more controllers and batteries. The controller governs the amount of electricity that flows from the batteries to the motor when the driver steps on the accelerator. The motor changes electrical energy from the batteries to mechanical energy, which makes the vehicle move.
Driving a battery EV down the road produces no pollution at all. Even when pollution related to power plant electricity production is factored in, these EVs produce less pollution than gasoline- or diesel-powered vehicles. Battery EVs are also more efficient than gasoline or diesel vehicles, if you compare the energy used in creating gasoline at a refinery to producing electricity in a power plant.
When a battery EV is stopped in traffic, it doesn’t have to use fuel to keep the motor running like a gasoline engine does. Added efficiency is created by something called “regenerative braking.” When the vehicle slows down, the motor continues to turn, but the power no longer flows to the wheels. Instead, the power is fed back to the batteries, giving them a small charge every time the driver stops or goes downhill.
Hybrid Electric Vehicles
A hybrid electric vehicle (HEV) uses two or more power sources. Most HEVs run on both a gasoline engine and an electric motor. They are similar in size and comfort level to the most popular gasoline-powered vehicles. There are now over 60 models of HEVs on the market, with the Toyota Prius remaining the top-selling HEV since its introduction in 2000.
The major components of an HEV include a gasoline engine, an electric motor, a transmission and, in some models, a generator. A fuel tank stores gasoline for the engine, and a battery pack stores electricity for the motor. The battery is charged by the gasoline engine and by the electric motor or generator during normal operation. Regenerative braking charges the batteries slightly when the car slows down, recovering some of the energy.
Plug-in Hybrid Electric Vehicles
Another type of hybrid electric vehicle is the plug-in hybrid, or PHEV. These vehicles have two power systems, an internal combustion engine and a battery. Unlike the regular hybrids such as the Toyota Prius, the PHEV’s battery can be recharged either by the gas engine or by plugging the vehicle into an external source of electricity. Some PHEVs are known as extended-range electric vehicles, or EREVs, because their secondary power source provides enough fuel to allow the vehicle to drive for hundreds of miles when the batteries become low.
All types of hybrid EVs use smaller, more efficient gasoline engines than conventional gasoline or diesel vehicles. They also burn less fuel than conventional vehicles, thus producing fewer pollutants and releasing less carbon dioxide into the air.
Use Energy Wisely at Home
Families that reduce their electricity use by avoiding waste and buying energy-efficient appliances save money and help preserve natural resources used to generate electricity.
Show your parents this list of ways to be energy-efficient and save money on your energy bills every month. Maybe you can persuade them to pass the cost savings on to you!
Lighting
- Install compact LED (light emitting diode) bulbs.
- Turn off lights when they’re not in use.
Heating/Air Conditioning
- Set your heater thermostat to the lowest temperature that still keeps you comfortable – some recommend 68°F by day and a cool 55°F by night.
- Ask an adult to make sure the fireplace damper is closed when the heating system is on so heated air doesn’t escape up the chimney.
- Keep your air conditioner’s thermostat set at 76°F to 78°F to stay comfortable and use less energy.
- Close doors quickly when you enter or leave a house where heating or air conditioning is on.
- Remind adults to have heating systems cleaned annually and to replace furnace filters regularly.
Appliances
- Use a clothesline when possible.
- Wait until the dishwasher is full before running it.
- Wash and dry full loads of laundry.
- Clean the coils on the refrigerator.
Cooking
- Cover pots when cooking.
- Don’t open the oven too often.
- Use the microwave whenever possible.
Bathing
- Install a low-flow showerhead.
- Take shorter showers or half-full baths.
- Turn down the thermostat on your water heater.
Transportation
- Walk.
- Use bicycles.
- Use buses, trains, and car pools.
- Combine errands to reduce trips.
Use Energy Wisely at School
Most schools spend more money on energy than on computers and textbooks combined. Here’s how you can help your school reduce energy waste.
Lights and Computers
- Pick an energy monitor to make sure lights and computers are turned off before recess, lunch and after school.
- Create a “Save Energy” sign to hang near your classroom light switches to remind people to turn lights off when not in use.
Heating and Cooling
- Make sure furniture or books do not block the vents in your classroom.
- Encourage everyone to keep doors and windows closed when heating or air conditioning is running.
Water
- Turn off the water in the bathroom when you are finished using it.
- Report any water leaks you find to your teacher or school custodian.
